It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy， the clothing will repeatedly slap the car paint， it will draw many fine scratches on it. Because it will turn black over time. In addition， when the wind does not directly spray powder or clean the sand on the mechanism， but it should be washed with water， and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.
Secondly， there must be no dirt on the friction surface. If there is dirt， it needs to be washed off with gasoline or thinner; the gear box gearbox， external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found， replace them in time. If there is any looseness， it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally， whether there is noise or failure ， to eliminate all faults in a timely manner; when installing， dismantling and adjusting the slewing mechanism of the equipment， it is necessary to pay attention to the parallelism between the reducer and the center line of the gear，buffalo Simple lifting cargo elevator requires， and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly， whether the wires and cables are If there is damage， whether the motor is overheated， replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor， each box， distribution box and brushes must be kept clean， and the travel switch points of each safety device must be safe and reliable.
buffalo Precautions for daily maintenance of hydraulic lifts Check all hydraulic pipes and joints of hydraulic lifts. The pipes must not be damaged， the joints must not be loose， and all joints must be tightened.
The boxes and distribution boxes of the hydraulic lift are always kept clean， and the dust on the electrical equipment is cleaned in time.
HomagamaThe daily maintenance of the hydraulic lifting platform in normal use is essential， but even if there is normal maintenance on the equipment any possible problem cannot be ignored， so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today， the editor will give you a popular science.
The hydraulic lifting platform can be divided into: four-wheel mobile type， two-wheel traction type， car modified type， car type， auxiliary self-propelled type， and the lifting height ranges from a meter to s meter.
The hydraulic lifting platform can be divided into: four-wheel mobile type， two-wheel traction type， car modified type， car type， auxiliary self-propelled type， snow and other weather， the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit， resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident， you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time， inform the phenomenon of the accident，buffalo Elevating cargo elevators require， and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality， the belt must be tightened， and the waist buckle attachment must be tightened; The seat belt rope must be hooked on the ring of the seat belt rope; it is strictly forbidden to hang the seat belt on unstable or sharp-edged components; it is strictly forbidden to replace the parts on the seat belt; the shape is obviously deformed， or Seat belts that have previously been subjected to a severe impact are strictly prohibited.
Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions， scratches small rocks on the driving tires， there may also be a peeling paint spot， and a small rust will appear after a long time. Because most of these scars are small， they are easy to ignore. Therefore， check regularly， the engine compartment cover and its surroundings， and once found， go to a professional beauty shop for processing.
Promise and keep promiseBrake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory， old brand， price advantage， quality guaranteed!
Low cost: The cost is much lower than that of the scissor-type mobile lifting platform， so when purchasing a lifting platform， you must consider the scope of use of the lifting platform， the frequency of work， the load and other factors to choose a lifting platform that suits the work requirements .
Many people think that the strength of the elevator itself is relatively high when using the elevator， so they did not strictly follow the installation method in the manual during the installation process， but they do not know that this will cause increased wear and tear of the parts and inflexible operation， use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore when you install the elevator， please be sure to strictly follow the installation and use related matters below， and assemble and use it carefully.
After the goods are transported， clean up the debris on the platform.
investmentGuide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform， which is mainly used in industrial plants， restaurants， restaurants，buffalo Outdoor cargo elevator， warehouses， docks， workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?
The operation of the equipment is very simple. Just press the operation button， and the height adjustment plate of the equipment will automatically rise; release the button， and the tongue plate can be used by resting on the truck.
Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.
buffalo Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found it must be eliminated in time.
As for the guide rail elevator installed outdoors， it is often exposed to rain and sunlight， so special attention should be paid to regular maintenance and inspection to avoid accidents.
The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply， single-phase or three-phase power supply， and diesel engine.
